The Americast installation instructions require a 2 x 4 stringer to be attached to the studs on the far wall which is about 5 feet in length. A stringer is just a stud itself cut to size. We moved the Americast tub into the recess and then pulled it away from the wall to expose the stringer. While we were doing this, Rob noticed the bathtub was a bit off level on the back left hand side. The instructions from American Standard have a schematic showing drywall screws being used to secure the tub.
Most of the time, though, the overflow valve needs a pipe attached to it that runs vertically downward to the bathtub waste pipe. The Americast tub eliminates the vertical overflow pipe by integrating it directly into the tub.
It went way smoother than we an anticipated and it was primarily due to the Americast tub design. Bathtub Installation. I wish our tub installation had been so simple and straight-forward! Nice work, and very descriptive explanation. Kenny, we set the tub directly on the wood subfloor and the instructions call for a cleat to be installed on the wall for extra support. We tested the structural integrity of the wood subfloor and reinforced the entire area.
Just the cement board space? Best guess, thank you, jasen. This was done because we wanted the cement substrate to jet out from the tub edge by about 4 inches. Thus the rough in for the right and left sides were about 32 inches wide. The back wall was approximately 60 inches wide.
The heights were 60 inches and we added purple board in order to get the walls to meet the ceilings but you can use cement board too. Was the bathroom the width of the tub? If so, how did you lay it flat and get it in position once through the door? We had to buy a separate kit that has the overflow and waste lines along with the pop up assembly. Jeff, I have to raise the BS flag.
The tub in this tutorial had a built-in overflow. Sorry for the confusion. I get a lot of questions these days and consequently get confused on some of the project details. Exactly what I am working at. I have had 3 tubs. First was odd size and getting the drain to connect was impossible. Second was too cheaply made. Working on third now. On the stringer board, how did you get it attached to the wall at the right height?
I figured it went up first and the tub slid up to it. Is that not the case? If I remember correctly the stringer was supposed to be attached to the studs at about 18 inches above the floor.
Would love your opinion. The floor is not level in an older home, so when I use the stringers to level it, one side is a good inch off the ground. The instructions say dont put any weight on the stringer.
But the runners are quite tall, and the instructions dont mention using a morter or expanding foam bed. Is using shims the only way to support it? How can I be sure the shims will stay in place if I just shim one end, but the rest of the runner is still off the ground? Any inside would be fantastic. Great questions Brendyn. One solution is to use 2x4s to damn off the area where the tub will go. Then use self-leveler in that tub are.
Allow the leveler to sit overnight then pull the 2x4s the next day. That will level your floor just where the tub goes. I believe you saying not to use drywall screws may deter people from using screws in general. Also telling people to ignore the manufactures directions I believe is very irresponsible.
Screws are certainly stronger at clamping which is exactly what the tub needs. I recommend you edit this article to follow manufacturer reccomendations and or show evidence of you overly broad opinion of strength of nails vs screws. Thanks Tim for your feedback. You can also use stainless steel screws and washers to accomplish the same affect as our roofing nails, this is an option. But I will never back down that drywall screws are a bad idea to hold a lb tub to the studs.
I appreciate your response. You said it best that every home owner must decide what is best for their situation. My bad for being an ass. Alcove Bathtubs Acrylic. Less than 6 Feet. View All. Alcove tubs, which are surrounded by walls on three sides. The front side is then covered with an integral tub apron. Right and left-handed drains are available and are selected depending on your bathroom configuration. ADA compliant shower faucets are easier, safer, and more comfortable for those with disabilities or limited mobility.
Find your nearest Wholesale Representative and choose from our great line of kitchen and bath products. Perfect 5' tub! Password Forgot Password Show Password. Don't have an account? Create an Account. Setting the standard. Last name. Confirm password Confirm password Show Password. Password Confirm password Show Password. Confirm password Show and Confirm Password.
Sign up to receive email updates and offerings. Create Account.
0コメント